The maintenance work and maintenance cycle setting of valves in daily use need to comprehensively consider multiple factors such as valve type, working environment, and frequency of use.
1. Maintenance work
Storage and maintenance
Valves should be stored in a dry and clean environment to avoid contact with corrosive substances.
For valves that are not used frequently, asbestos packing should be removed to prevent electrochemical corrosion.
The inlet and outlet of the valve should be sealed with wax paper or plastic sheets to prevent debris from entering.
Use and maintenance
Check the valve stem thread regularly and apply lubricant to reduce friction.
For valves that are not opened and closed frequently, the handwheel should also be turned regularly to prevent the valve stem from biting.
Outdoor valves should be covered with protective covers to prevent rain, snow, dust and rust.
Always keep the valve clean, check and maintain the integrity of valve parts.
Packing maintenance
Packing is a key component of valve sealing. It should be checked regularly for aging or failure and replaced in time.
After the valve is installed in the pipeline, due to factors such as temperature, external leakage may occur. At this time, the nuts on both sides of the packing gland should be tightened in time to ensure sealing.
Grease injection maintenance
According to the valve type and sealing capacity, inject an appropriate amount of grease.
When injecting grease, pay attention to the injection pressure, injection amount, switch position and other issues to ensure the injection effect.
After grease injection, the injection port should be sealed to prevent impurities from entering.
2. Setting the maintenance cycle
Valve type
Ball valve: Under normal working conditions, ordinary ball valves should be fully maintained and inspected every 1 to 2 years. For ball valves that are frequently opened and closed or used for high temperature, high pressure, and highly corrosive media, the maintenance cycle may need to be shortened to half a year to 1 year.
Butterfly valve: Ordinary butterfly valves are usually maintained every 1.5 to 2 years. Large-diameter butterfly valves or butterfly valves used in harsh working conditions, such as butterfly valves in sewage discharge, seawater desalination, etc., are recommended to be maintained once every 1 year or so.
Gate valve: Manual gate valves are generally maintained every 2 to 3 years. Due to their complex drive mechanisms, electric or pneumatic gate valves are recommended to be fully inspected and maintained every 1 to 1.5 years.
Globe valve: The maintenance cycle of globe valves is usually 1 to 2 years. Stop valves used for media that are frequently opened and closed or contain particulate impurities may need maintenance every six months to one year.
Working environment
Temperature: Valves working in high temperature environments, such as valves on high temperature steam pipelines, may require more frequent maintenance due to factors such as thermal expansion of materials and aging of seals. They are generally inspected and maintained every six months to one year. Valves working in low temperature environments, such as valves on liquefied natural gas pipelines, also need to regularly check their sealing performance and low temperature adaptability of materials. The maintenance cycle is usually 1 to 1.5 years.
Pressure: High-pressure valves have high requirements for sealing performance and component strength due to the high pressure they bear. The maintenance cycle is generally six months to one year. Low-pressure valves only need maintenance every 1 to 2 years under normal circumstances.
Medium characteristics
If the medium is corrosive, abrasive or contains impurities, the wear and corrosion rate of the valve will accelerate, and the maintenance cycle needs to be shortened. For example, valves on pipelines that transport corrosive media such as acids and alkalis may need to be inspected and maintained every 3 to 6 months; valves that transport water containing sand need to be maintained every 6 months to one year.
Frequency of use
For valves that are frequently opened and closed, such as in the fluid control system of an automated production line, it is recommended to conduct a simple inspection every 1 to 3 months and a comprehensive maintenance every six months to one year. For valves that are occasionally opened and closed, such as valves on spare pipelines, the maintenance cycle can be appropriately extended to 2 to 3 years, but a simple inspection is still required before each use.
Critical parts
Valves in critical parts, such as emergency shut-off valves in nuclear power plants and chemical production, fuel delivery valves in aerospace, etc., usually have a shorter maintenance cycle and may require strict inspection and maintenance every 1 to 3 months.





